Den EXAKTA skillnaden mellan 996 GT3 och 996 GT3 RS
Detta är skillnaden mellan 996 GT3 och 996 GT3 RS enligt Porsches tekniska dokumentation
Engine
The engine of the 911 GT3 is used in the 911 GT3 RS in model year 2004. The geometry of the inlet ports in the cylinder head have been optimised. This resulted in a new engine type, which for this vehicle is esignated M79/80. Additional information is available in the existing Technical Service Information brochures and in the Corporate Porsche Academy.
Fuel and ignition system
ME 7.8 Motronic control unit. The data record "GT3 RS EU4" is available for programming the Motronic
control unit.
Air ducts of intake air system
The 911 GT3 RS has modified air ducting of intake air from the rear lid to the air cleaner. A RAM air inlet on the rear lid improves engine induction at higher speeds through ram induction.
Exhaust tailpipes
The polished exhaust tailpipes of the 911 GT3 RS have a ground surface look.
Spark plugs
The 911 GT3 RS is fitted with special spark plugs with M12 x 1.25 thread and 2 earth electrodes, which are to be replaced every 40,000 km.
Transmission
The G96/90 type transmission along with the complete clutch is taken unchanged from the GT3 model of 2004.
Flywheel
To reduce the masses of the crankgear to a minimum, a single-mass flywheel is used on the 911 GT3 RS.
Chassis and suspension
The chassis and suspension, including the brake system of the 911 GT3 RS, has been adopted in its basic components from the 911 GT3. In order to accommodate the higher power ratios and driving dynamics, modification of the front and rear axle wheel carriers and further tuning on the springs, shock absorbers and stabilizers has taken place. The following only describes the changes in relation to the 911 GT3.
Front axle Wheel carrier
The wheel carrier is a sand-cast, hollow component manufactured with torsional and bending strength. The spring strut (A) is clamped in place with two bolts. The mounting points of the lateral control arms and track rods (B) have been lowered to optimize the kinematics and the position of the lower lateral control
arms. The wheel carrier is secured with a pressure plate and six bolts (C).
Spring strut
The spring strut consists of a single-tube gas-filled shock absorber and a spring adapted to the driving dynamics (45 N/mm). The lower, heightadjustable spring seats allow raising or lowering of the ride height as well as fine adjustment of the wheel loads.
Rear axle wheel carrier
The wheel carrier is a sand-cast, hollow component manufactured with torsional and bending strength. The mounting points of the lateral control arms and tie rod arms have been lowered to optimize the kinematics
and the position of the lower lateral control arms. The wheel carrier is secured with a pressure plate and six bolts.
Lower lateral control arm
The lower lateral control arms, as on the front axle, are in two parts for optimum camber adjustment. Basic camber adjustment is carried out by inserting shim plates. Fine adjustment is still carried out via the camber eccentric. The casting is the same for the front and rear axle. However, as the rubber mountings for the longitudinal control arms are provided with elongated holes (A), the installation position is to be noted. Arrow = driving direction
Rear axle side section, track and camber eccentric
Because the stroke of the track and camber eccentric have been increased, the side sections in this area have been modified accordingly. The support of the eccentric is only at the front.
Stabilizers
The stabilizers on the front and rear axle have been taken unchanged from the 911 GT3. The position of the twist beam on the stabilizer has been adapted to the driving dynamics.
Parallélisme
The wheel position values have been modified to further improve the driving dynamics.
To prevent excessive wear at the support points, the screw fastenings should be well loosened before adjusting. Data and adjustment values as well as position of the twist beams on the stabilizer can be found in the Technical manual.
Body
The basis for the body of the 911 GT3 RS is the 911 GT3 in the Clubsport version, model year 2004.
Front hood
The front hood is only painted on the outside and is manufactured from the material CFRP (carbon fiber reinforced plastic). The inside is finished in carbon look. The Porsche emblem is adhered on in film form. The second gas-filled spring is discontinued.
Engine compartment lid
The engine compartment lid is as on the 911 GT3, model year 2004. On this, the large carbon look rear wing is mounted, along with a plastic air intake scoop for ducting the intake air.
Body equipment, exterior
The basis for the body equipment, exterior of the 911 GT3 RS is the 911 GT3, model year 2004. The vehicle has no side airbags.
Colors
The basic color of the 911 GT3 RS is carrara white. Options are red or blue "GT3 RS" logo stickers applied to the doors and on the rear. The wheel centers are painted red or blue respectively.
Front trim
The front trim has additional openings at the top for the radiator outlet air. The air duct behind the middle radiator guides the air through the outlet in the top of the front trim. Wire mesh grilles are fitted in front of the air intakes and outlet opening.
Rear window
The rear window is made of plastic (polycarbonate).
Rearview mirror
The rearview mirrors are finished in carbon look.
Seat belts
The color of the seat belts is red for the carrara white/red color combination and
blue for carrara white/blue.
Body equipment, interior
The body equipment, interior of the 911 GT3 RS equates to that of the 911 GT3 Clubsport, model year 2004. The steering wheel rim is in Alcantara sewn with red or blue thread (depending on selected color combination). Alcantara is also used on the gear lever and handbrake lever handle, sewn with red or blue thread. The vehicles have no glovebox and no cup holder.
Door panel
The door panels have storage compartments in place of loudspeakers.